OEM Button коды элементов MACH

Обновлено7.04.2019 - 22:48

Screen 1	1
Screen 2	2
Screen 3	3
Screen 4	4
Screen 5	5
Screen 6	6
Screen 7	7
Screen 8…98	8…98
Screen 99	99
Jog Increment Increment	100
Jog Increment Decrement	101
Reset Interp	102
Jog Enable Off/On Toggle	103
Safe Z Height Go To	104
"Home/Reference All Z Then X,Y,A,B,C Set Coords"	105
Units Inch/MM	106
Multi-function DROs Machine/Work Toggle 1	107
Feed Rate Override Increment (percentage)	108
Feed Rate Override Decrement (percentage)	109
Spindle CW Off/On Toggle	110
Jog Slow Increment	111
Jog Slow Decrement	112
Coolant Flood Off/On Toggle	113
Coolant Mist Off/On Toggle	114
G-code Edit	115
Rotational axis Diameter A Zero A	116
Part A Zero	142
Part B Zero	143
Part C Zero	144
Tool X Touch	145
Tool Z Zero	146
Joystick Throttle	147
Tool Touch Correction Enable Off/On Toggle	148
"Homing/Limits Auto Over Ride Limit/Home Switches"	149
Homing/Limit Switch Over Ride (Manual)	150
SS on Act4 Off/On Toggle	151
Reserved	152
Reserved	153
Reserved	154
Units Per Minute/Rev. Toggle	155
Set Next Line	156
Tool Path Jog Follow	157
Joystick On	158
Joystick Off	159
Tool Path Regen Display	160
Work X-Z Zero (turn)	161
Coordinate Mode Abs./Incremental.	162
"Spindle Speed Override Increment by (percentage)"	163
"Spindle Speed Override Decrement by (percentage)"	164
Laser Trigger Enable Off/On Toggle	165
Laser Grid Zero	166
Z Limiting Off/On Toggle Z	167
Tool Change Ignore Off/On Toggle	168
G-Code Close current File	169
G-Code Re-load Last File	170
Jog increment Selection Cycle	171
Clear error Label	172
Spindle CCW Off/On Toggle	173
MPG Parallel Port Encoder 3 Jog Off/On Toggle	174
MPG 1 Cycle Axis Controlled	175
Block Delete	176
Optional Stop Off/On Toggle	177
Inhibit All Off/On Toggle	178
"Multi-function DROs Machine Coordinates Displayed"	179
Multi-function DROs Work + G 92	180
Multi-function DROs Work	181
"Spindle ??? (Override cancel)Actual Off/On Toggle"	182
Home/Reference X Then Z (turn)	184
MPG 1 Jogs X	185
MPG 1 Jogs Y	186
MPG 1 Jogs Z	187
MPG 1 Jogs A	188
MPG 1 Jogs B	189
MPG 1 Jogs C	190
Jog Increment Selection 1	191
Jog Increment Selection 2	192
Jog Increment Selection 3	193
Jog Increment Selection 4	194
Jog Increment Selection 5	195
Jog Increment Selection 6	196
Jog Increment Selection 7	197
Jog Increment Selection 8	198
Jog Increment Selection 9	199
Jog Increment Selection 10	200
Joystick Feed Rate Override Off	201
Joystick Feed Rate Override Jog	202
Joystick Feed Rate Override Feed	203
Jog Mode Continuous 1	204
Jog Mode Incremental 1	205
Joystick On	206
Joystick Off	207
Tool Z Clear (turn)	208
Tool X Clear (turn)	209
Tool Touch Stock Correction Set to Zero	210
Home/Reference X and Z (turn)	211
Home/Reference X (turn)	212
Home/Reference Z (turn)	213
G-Code Show Recent Files	214
Display History	215
G-code Load	216
Tool Post Front/Rear Toggle	217
Z Limiting ON Z	218
Z Limiting Off Z	219
Port Bit-Test	220
Torch Height Correction Off/On Toggle	221
Torch Height Correction Off	222
Torch Height Correction ON	223
Coolant Flood ON	224
Coolant Flood Off 225
Coolant Mist ON	226
Coolant Mist Off	227
Teach File Load	228
Tool Path in Machine/Work Toggle	229
Wizard Display Selection Window	230
Wizard is done Load normal screen	231
Screen Simple/Complex Toggle	232
Output 4 On	233
Output 4 Off	234
Output 5 On	235
Output 5 Off	236
Output 6 On	237
Output 6 Off	238
Set Help Context	239
Home/Reference All Forced De-Reference	240
Tangential Off/On Toggle	241
G 59 Work Save Current XYZ to G 59.254 XYZ	242
Coordinates Machine G 53 Do G0G53	243
G 59 Move to G59.254 with midpoint selection	244
"Jog Mode Continuous/Incremental/MPG Toggle Through"	245
Home/Reference All Forced	246
CV Off/On Toggle	247
CV OFF 248
CV On 249
Jog Inhibit X Off/On Toggle 250
Jog Inhibit Y Off/On Toggle 251
Jog Inhibit Z Off/On Toggle	252
Jog Inhibit A Off/On Toggle	253
Jog Inhibit B Off/On Toggle	254
Jog Inhibit C Off/On Toggle	255
Multi-function DROs Machine/Work Toggle 2	256
Inhibit All Off	257
Inhibit All On	258
Encoder Jog X	259
Encoder Jog Y	260
Encoder Jog Z	261
Encoder Jog A	262
Encoder Jog B	263
Encoder Jog C	264
Jog Increment Value 1	265
Jog Increment Value 2	266
Jog Increment Value 3	267
Jog Increment Value 4	268
Jog Increment Value 5	269
Jog Increment Value 6	270
Jog Increment Value 7	271
Jog Increment Value 8	272
Jog Increment Value 9	273
Jog Increment Value 10	274
Jog Mode Incremental 2	275
Jog Mode Continuous 2	276
Feed Rate Increment (units)	277
Feed Rate Decrement (units)	278
Reverse Run	279
Wizard Switch to Last Used	280
MPG 2 Cycle Axis Controlled	281
MPG 2 Taper Mode Off/On Toggle	282
MPG Dual Flag Off/On Toggle	283
MPG Shuttle mode Off/On Toggle	284
Pause Preparation Moves	285
Pause (remember state)	286
Feed Rate Rapid Override On/Off Toggle	287
Dwell Crop current now	288
Set Formulas	289
MPG Push To Stop Jog X	290
MPG Push To Stop Jog Y	291
MPG Push To Stop Jog Z	292
MPG Push To Stop Jog A	293
MPG Push To Stop Jog B	294
MPG Push To Stop Jog C	295
Motor Screw Mapping	296
Dwell Unconditional crop any now	297
Reserved	298
Feed Rate Alternative Bypass Off/On Toggle	299
Tool Post Front/Rear Toggle	300
"Code for OEMTriggers runs the macro in SetTriggerMacro 301"	301
"MPG Steps Multiple/Single/Step Velocity/Velocity Only Toggle"	302
MPG Velocity Only	303
MPG Step/Velocity	304
MPG Steps Single	305
MPG Steps Multiple	306
Jog Push To Jog X Positive	307
Jog Push To Jog X Negative	308
Jog Push To Jog Y Positive	309
Jog Push To Jog Y Negative	310
Jog Push To Jog Z Positive	311
Jog Push To Jog Z Negative	312
Jog Push To Jog A Positive	313
Jog Push To Jog A Negative	314
MPG Calibrate	315
Tool Table Save	316
Work Table Save	317
Tool Path Mouse Drag Zooms Off/On Toggle	318
Tool Path Mouse Drag Pans Off/On Toggle	319
Wizard Display Selection Dialog	320
Wizard Run Newfangled	321
Emergency bailout	322
Screen Visibility of Screen 50 Off/On Toggle	323
Tool X Touch (turn)	324
"Torch Volts Controlled by Spindle Step Line Off/On Toggle"	325
Tool Z Touch (turn)	326
MPG Jog Mode	327
unknown	328
Jog Push To Jog B Positive	329
Jog Push To Jog B Negative	330
Jog Push To Jog C Positive	331
Jog Push To Jog C Negative	332
Multi-function DROs Distance To Go	333
Jog Push To Jog X Stop	334
Jog Push To Jog Y Stop	335
Jog Push To Jog Z Stop	336
Jog Push To Jog A Stop	337
Jog Push To Jog B Stop	338
Jog Push To Jog C Stop	339
Soft limits Set Temporary Minimum	340
Soft limits Set Temporary Maximum	341
Reserved 343-346	347
Screen Menu Bar Turn Off	348
Screen Menu Bar Turn On	349
Spindle Speed Requested Increment by (value)	350
Spindle Speed Requested Decrement by (value)	351
Jog Together X & A ++	352
Jog Together X & A –	353
Jog Together Y & B ++	354
Jog Together Y & B –	355
Start	1000
Pause Feed Hold	1001
G-Code Rewind	1002
Stop	1003
Single Block	1004
Resume	1005
Teach File Edit	1006
Work Zero All	1007
Work X Zero	1008
Work Y Zero	1009
Work Z Zero	1010
Work A Zero	1011
Work B Zero	1012
Work C Zero	1013
Feed Rate Override Cancel	1014
Estimate Job	1015
Run From Here	1016
Work Go To Zeros	1017
Multi-function DROs System	1018
Verify	1020
Reset	1021
Home/Reference X	1022
Home/Reference Y	1023
Home/Reference Z	1024
Home/Reference A	1025
Home/Reference B	1026
Home/Reference C	1027
Joystick Off/On Toggle	1028
Soft limits On/Off Toggle	1029
Unknown	1030
Jog Push to Jog Until stopped	1031

Если Вам понравилось статья OEM Button коды элементов MACH , поделитесь с друзьями :

Копирование информации без ссылки на публикацию запрещено!!!